3M™ PPS™ Series 2.0 Spray Cup System Kit, 26000, Standard (22 fl oz, 650 mL), 200 Micron Filter, 1 kit per case
-
Return Policy
Our site states no returns allowed; however, in addition to a few exceptions, if your order is defective or damaged, the order will be replaced with good product.
-
Lead Time2
-
Manufacturer3M
-
SAP7100134641
-
3M ID60455003529
-
UPC00-51131-26000-9
-
Product Formal Name3M™ PPS™ Series 2.0 Spray Cup System Kit, 26000, Standard (22 fl oz, 650 mL), 200 Micron Filter, 1 kit per case
-
BrandPPS
-
Case UnitCase of 1
-
Unit of MeasureKit
-
Part Number26000
-
Estimated Lead Time2
-
Inventory Status CodeS
-
Country of OriginUSA
-
Return PolicyNo Return
-
Box Length (in)15.9
-
Box Width (in)13.9
-
Box Height (in)10.8
- Bullets
-
Bullet 13M™ PPS™ Series 2.0 is our next generation, highest performing disposable spray cup system;New quarter-turn lid locking system locks lid to cup and eliminates paint build up and cross threading;Redesigned adapters provide four points of connection from spray gun to lid, improving stability and confidence especially in large applications;Domed lid geometry and a wider fluid spout allows up to 3 fl. oz. (90 mL) of material to be held below the filter reducing inconsistent spray due to air-entrapment and sputter;Full-diameter filters are built into every lid for the highest quality filtration; aids with fluid flow;A new reusable hard cup is included in every lid/liner kit;Mixing ratios are printed on each cup and a clear access window allows users to grasp liner while removing the lid, making tinting/refilling easier;Enlarged sealing plugs provide stable base for cups to be placed upside down, keeping filters wet during temporary sealing and protection of coatings not in use;3M™ PPS™ (Legacy) red dispensers can be used with 3M™ PPS™ Series 2.0;3M™ PPS™ reduces cleaning solvent consumption by up to 70% and reduces prep and clean-up time by up to 50%; compared to conventional paint cup systems
-
- Transportation
-
ECCN NumberEAR99
-
Harmonized Tariff Schedule Number8424909080
-
United States Department Of Transportation Ground US DOT, 49 CFRNOT REGULATED
-
United States Department Of Transportation Vessel US DOT, 49 CFRNOT REGULATED
-
NMFC Item156600
-
NMFC Class250.0
-
NMFC Sub03
-
Transport Protective ServicePROTECTIVE SERVICE NOT REQUIRED
-
International Air Transport AssociationNOT REGULATED
-
International Maritime OrganizationNOT REGULATED
-
Flashpoint TransportNo Flash Point
-
Our site states no returns allowed; however, if your order is defective or damaged, the order will be replaced with good product. In addition, we will attempt to return all your product (not only damaged product) if 3M grants the return based on various factors. Some items may be approved for return pending approval from 3M. Some but not all factors include if the item is a 3M stock item and elapsed time from receipt of product to issued return request. Note: 3M will not accept a return if the item is made to order or if the order is less than $600.00. Please double check accuracy of your orders prior to placing them. Details regarding if an item is stock or made to order can be found in the specifications tab of the item page. N = Made to order Item. S = Stock Item. We cannot guarantee any returns.
If you received a defective or damaged shipment, please email us at support@industrialgeneralstore.com explaining in detail the reason for requesting a replacement so we can contact 3M and initiate the return and new shipment.