3M™ PPS™ Collar, 16345, Midi (13.5 fl oz, 400 mL), 75 collars per case

3M™ PPS™ Midi Collar, Bulk packaging for 3M OUS subsidiaries
Estimated Lead Time is 25 working days.
Request price
  • Return Policy

    Our site states no returns allowed; however, in addition to a few exceptions, if your order is defective or damaged, the order will be replaced with good product. 

    • Weight
      6.7 lbs
    • SKU
      7010364397
    • UPC/ISBN
      00051131163454
  • Industry
    IB
  • Lead Time
    25
  • Manufacturer
    3M
  • SAP
    7010364397
  • 3M ID
    60455066849
  • UPC
    00-51131-16345-4
  • Product Formal Name
    3M™ PPS™ Collar, 16345, Midi (13.5 fl oz, 400 mL), 75 collars per case
  • Brand
    PPS
  • Case Unit
    Case of 75
  • Unit of Measure
    Case
  • Estimated Lead Time
    25
  • Inventory Status Code
    N
  • Country of Origin
    USA
  • Return Policy
    No Return
  • Box Length (in)
    13.8
  • Box Width (in)
    9.9
  • Box Height (in)
    7.4
  • Bullets
    • Bullet 1
      - Bulk PPC Number for 3M OUS Subsidiaries to order Midi (400mL) size PPS Collars - Only - 75 per box
      - Collars are a locking mechanism for the 400mL Midi size PPS
      - To be used with the 400mL Midi Size PPS
      - Also available as part of sets with PPS™ Cups
      - 3M™ PPS™ is an all-in-one disposable solution for measuring, mixing, filtering, and spraying of paint materials
      - System enables the painter to consistently spray at 90° to the part, no matter the part orientation (even upside down)
      - All-in-one solution reduces the chance of outside contamination and reduces paint consumption
      - Reduces cleaning solvent consumption up to 70% and reduces prep and clean-up time up to 50%
      - System delivers improved quality, lower material cost, less solvent consumption, improved productivity, less mess and easier use
  • Transportation
    • ECCN Number
      EAR99
    • Harmonized Tariff Schedule Number
      8424909080
    • UNSPSC Code
      25000000
    • United States Department Of Transportation Ground US DOT, 49 CFR
      NOT REGULATED
    • United States Department Of Transportation Vessel US DOT, 49 CFR
      NOT REGULATED
    • NMFC Item
      156600
    • NMFC Class
      092.5
    • NMFC Sub
      07
    • Transport Protective Service
      PROTECTIVE SERVICE NOT REQUIRED
    • International Air Transport Association
      NOT REGULATED
    • International Maritime Organization
      NOT REGULATED
    • Flashpoint Transport
      No Flash Point
  • SKU
    7010364397
  • UPC/ISBN
    00051131163454

Vital Parts for Using 3M™ PPS™Designed specifically for use with the 3M™ Paint Preparation System, these Midi (13.5 oz.)-sized 3M™PPS™ Collars twist on to from a tight seal between PPS™ Cups and PPS™ Lids for optimized spray performance. They also help support disposable 3M™PPS™Liners, reducing accidental leakage into reusable cups. The Midi size suits a range of jobs.These 3M™PPS™ Collars are sold in bulk (75 Collars per box). They are also available pre-matched with corresponding Midi-sized 3M™ PPS™ Cups.Advantages of the 3M™ PPS™SystemUnlike conventional paint cup systems, our 3M™ PPS™ eliminates the need for mixing paint in additional paint mix cups and then transferring the paint through a separate filter into a paint reservoir. This is an important advantage because waste occurs every time that a user transfers paint through mixing cups and filters. With PPS™, you place the disposable liner within the re-usable PPS™Cup. Then simply mix the paint in the PPS™disposable liner, snap the disposable lid (with the pre-welded filter) in place and attach the locking collar to complete the PPS™System. With just these few simple steps, you#39;re ready to start spraying.Your Spray Gun Functions at any Angle, Even Upside DownPPS™allows the painter to spray consistently 90 to the part, no matter how the part is positioned. This makes material transfer more consistent, limits paint overspray and lowers paint consumption. Because PPS is a closed system, you can operate in any orientation - i.e. 360 degrees.Clean Up is a Breeze and Uses Less SolventAfter spraying, the painter can use a sealing plug to seal and protect paint materials or simply discard disposable lid and liner, leaving only the adapter and spray gun to clean. Discard the disposable lid and liner in the appropriate approved waste containers specified by the paint manufacturer and local government requirements. Use a small amount of solvent for cleaning the spray gun and the PPS™adapter. With this disposable paint system, shops are often experiencing up to a 70% reduction in cleaning solvents, which means solvent cleaning savings and solvent disposal savings.Most guns can be cleaned with less than 3 oz. of solvent.A Versatile System that Works with Most Spray GunsSpecifically designed PPS™stainless steel metal adapters allow painters to use the PPS™ system with virtually any spray gun.Painters have also the option to use the 3M™ Accuspray™ ONE spray gun, which requires no adapters. Technicians have found that this spray gun further reduces cleaning solvent usage and cleaning and maintenance time.Reduces the Chance of Contamination Between JobsBecause the painter uses a new disposable lid (with welded-in filter) and disposable liner for each mix, there is less risk of outside contamination due to mixing, filtering, and clean up. Using a fresh lid and liner with each paint job, rather than washing out reusable components, often improves overall productivity in prep and clean-up time by as much as 15%.The Bottom Line: Why 3M is the Paint & Coatings Spray System of Choice3M™ PPS™ is an all-in-one disposable painting system that produces cleaner jobs, saves on paint consumption and reduces solvent usage by up to 70%. You#39;ll find that technicians operate with greater efficiency and spend le

FREIGHT FREE on purchases with a subtotal of $4000.00 or more.

Our site states no returns allowed; however, if your order is defective or damaged, the order will be replaced with good product. In addition, we will attempt to return all your product (not only damaged product) if 3M grants the return based on various factors. Some items may be approved for return pending approval from 3M. Some but not all factors include if the item is a 3M stock item and elapsed time from receipt of product to issued return request. Note: 3M will not accept a return if the item is made to order or if the order is less than $600.00. Please double check accuracy of your orders prior to placing them. Details regarding if an item is stock or made to order can be found in the specifications tab of the item page. N = Made to order Item. S = Stock Item. We cannot guarantee any returns.

If you received a defective or damaged shipment, please email us at support@industrialgeneralstore.com explaining in detail the reason for requesting a replacement so we can contact 3M and initiate the return and new shipment.

3M PPS Paint Preparation System
3M Paint Cup
3M PPS Paint Preparation System Tech Tips