Standard Abrasives™ Buff and Blend HS Flap Brush 875371, 14 in x 1-1/2 in x 8 in FB119 23-11 HD A MED, 3 per case

Designed to utilize the material face rather than the edge, our Standard Abrasives™ Buff and Blend HS Flap Brush helps achieve fine finishes without leaving lines on the workpiece. The high strength (HS) material makes it an ideal choice for blending, cleaning, deburring and finishing on stainless steel, brass and aluminum, especially where uniform and long line brushed finishes are desired.

Price: $685.33

(Case of 3 Each)

Estimated Lead Time is 15 working days.
  • $685.33
  • Case of 3 - $685.33
  • Return Policy

    Our site states no returns allowed; however, in addition to a few exceptions, if your order is defective or damaged, the order will be replaced with good product. 

    • Weight
      9.6 lbs
    • SKU
    • UPC/ISBN
  • Industry
  • Lead Time
  • Manufacturer
  • SAP
  • 3M ID
  • UPC
  • Product Formal Name
    Standard Abrasives™ Buff and Blend HS Flap Brush 875371, 14 in x 1-1/2 in x 8 in FB119 23-11 HD A MED, 3 per case
  • Brand
    Standard Abrasives
  • Case Unit
    Case of 3
  • Unit of Measure
  • Estimated Lead Time
  • Grit/Micron
  • Size
    14 in x 1-1/2 in x 8 in
  • Inventory Status Code
  • Data Sheet
  • Instructions/Manual
  • Country of Origin
  • Return Policy
    No Return
  • Width
    14 in
  • Length
    1-1/2 in
  • Box Length (in)
  • Box Width (in)
  • Box Height (in)
  • Bullets
    • Bullet 1
      - Provides decorative, High luster finishes on stainless steel, brass and aluminum
      - tough nylon face removes surface contaminants without leaving lines or gouging the Work piece
      - High strength durability is tear-resistant and stands up to irregular shaped parts
      - open web design resists loading and eliminates metal contamination of workpiece
      - Resin coated surface runs cool and is Waterproof for Use with lubricants
      - various sizes Available for wide range of tools: Straight shaft Portable grinder, bench motor, backstand, floor lathe, rotary, Straight line, and robotic
  • Transportation
    • ECCN Number
    • UNSPSC Code
    • United States Department Of Transportation Ground US DOT, 49 CFR
    • United States Department Of Transportation Vessel US DOT, 49 CFR
    • NMFC Item
    • NMFC Class
    • NMFC Sub
    • Transport Protective Service
    • International Air Transport Association
    • International Maritime Organization
    • Flashpoint Transport
      No Flash Point
  • SKU

Quality Materials Well-Suited for Deburring and Finishing Irregular-Shaped PartsOur Buff and Blend High Strength products are made from tough, resin-reinforced nylon fiber with aluminum oxide abrasive grain. The durable high strength construction of our Standard Abrasives™ Buff and Blend HS Flap Brush provides aggressive action for the toughest applications and provides greater tear resistance, perfect for deburring or final finishing on irregularly shaped parts. Tough, non-woven Buff and Blend HS material allows removing surface contaminants without eliminating critical detail or gouging the workpiece. Choose from a broad offering of sizes, densities and grades to suit many different finishing operations.Medium Grade Brush Suits Decorative and In-Line ApplicationsWhen a very fine high luster and decorative finish is desirable on pieces such as builders hardware, the HS Brush in MED grade provides the conformability you need.The Buff and Blend HS Flap Brush is an ideal choice for:A grain finish on brass strike plates for door hardwareA satin finish on builders' hardware (cabinet handles, door knobs, and more)Satin finishes on soft metalsHighlighting and finishing aluminum extrusions (used as a quality control tool to identify defects)Inline brushed finishes on aluminum and stainless cookware (pots and pans)Producing fine scratch patterns on utensils and cutlery prior to cotton buff and compound polishingRemoving oxide from precious metalsFeaturing Consistent Finishes and Operator ComfortFlap brushes produce a consistent finish which does not reflect lines commonly attributed with ganged arbor hole discs. Density, pressure and angle determine the ability of the flap brush to remove burrs, oxidation and handling marks. The abrasive brush material provides ventilation which helps dissipate heat and, therefore, runs cooler. This provides consistent finishes without smearing or otherwise discoloring the work piece. Minimal vibration can reduce chattermarks on the workpiece and can lead to less operator and machine fatigue.Load-Resistant Construction Boosts Life and PerformanceStandard Abrasives™ Buff and Blend products are load-resistant to keep you cutting with fresh mineral.The gaps in the open web allow unwanted swarf to escape. Consequently, less debris clogs the abrasive, so the mineral can stay fresh, keep cutting sharp and deliver a consistent cut over the life of the product. As the fibers break down and fresh mineral is exposed, it reduces the likelihood of dull or blunt mineral smearing the surface, contributing tocleaner surfaces and less re-work. Furthermore, manual fatigue that may result from applying heavy pressure to a dull abrasive is reduced.The Many Benefits of Standard Abrasives™ Buff and Blend ProductsStandard Abrasives™ Buff and Blend products invigorate deburring, cleaning, blending and finishing applications by helping operators reduce finishing steps, minimizecosts and achievegreaterthroughput. Each Buff and Blend product and grade offers unique benefits, so operators can choose from a versatile range of options to ensure superior performance on specific applications.

FREIGHT FREE on purchases with a subtotal of $4000.00 or more.

Our site states no returns allowed; however, if your order is defective or damaged, the order will be replaced with good product. In addition, we will attempt to return all your product (not only damaged product) if 3M grants the return based on various factors. Some items may be approved for return pending approval from 3M. Some but not all factors include if the item is a 3M stock item and elapsed time from receipt of product to issued return request. Note: 3M will not accept a return if the item is made to order or if the order is less than $600.00. Please double check accuracy of your orders prior to placing them. Details regarding if an item is stock or made to order can be found in the specifications tab of the item page. N = Made to order Item. S = Stock Item. We cannot guarantee any returns.

If you received a defective or damaged shipment, please email us at explaining in detail the reason for requesting a replacement so we can contact 3M and initiate the return and new shipment.