Scotch-Brite™ EX2 Deburring Wheel, X2-WL, 8A Medium, 8 in x MISC x 3 in, Config

Scotch-Brite™ EX2 Deburring Wheel is a convolute-constructed wheel that provides mid-range aggressiveness and hardness for deburring, edge radius, blending, polishing, and finishing. Our deburring wheel performs best when consistently presented with a sharp edge or metal burrs.
Estimated Lead Time is 10 working days.
Request price
  • Return Policy

    Our site states no returns allowed; however, in addition to a few exceptions, if your order is defective or damaged, the order will be replaced with good product. 

    • Weight
      3 lbs
    • SKU
      7100130671
    • UPC/ISBN
      00076308207922
  • Industry
    IB
  • Lead Time
    10
  • Manufacturer
    3M
  • SAP
    7100130671
  • 3M ID
    61000501793
  • Product Formal Name
    Scotch-Brite™ EX2 Deburring Wheel, X2-WL, 8A Medium, 8 in x MISC x 3 in,
    Config
  • Brand
    Scotch-Brite
  • Case Unit
    Case of 1
  • Unit of Measure
    Each
  • Product ID
    X2-WL
  • Estimated Lead Time
    10
  • Grade
    Medium
  • Grit/Micron
    Medium
  • Size
    8 in x MISC x 3 in
  • Inventory Status Code
    Configurable
  • Country of Origin
    USA
  • Product Form
    Wheel
  • Return Policy
    No Return
  • Width
    8 in
  • Length
    MISC
  • Bullets
    • Bullet 1
      - wheel edge can be dressed for effective deburring, finishing and polishing of all metal alloys and many plastics and composites
      - tough, layered, unitized construction can operate clockwise or counterclockwise directions
      - densities and grades ranging from soft and Conformable to hard and aggressive offer utility for a wide variety of applications
      - resists smearing for cleaner surfaces and less preparation
      - Minimizes heat build up to lessen impact on heat-sensitive materials
  • Transportation
    • ECCN Number
      EAR99
    • UNSPSC Code
      31191600
    • United States Department Of Transportation Ground US DOT, 49 CFR
      NOT REGULATED
    • United States Department Of Transportation Vessel US DOT, 49 CFR
      NOT REGULATED
    • NMFC Item
      001020
    • NMFC Class
      055.0
    • NMFC Sub
      00
    • Transport Protective Service
      PROTECTIVE SERVICE NOT REQUIRED
    • International Air Transport Association
      NOT REGULATED
    • International Maritime Organization
      NOT REGULATED
    • Flashpoint Transport
      No Flash Point
  • SKU
    7100130671
  • UPC/ISBN
    00076308207922

Our high performance combination of mineral (aggressiveness) and density (hardness) make the Scotch-Brite™ EX2 wheel uniquely suited to applications where a moderate degree of conformability, wheel hardness, and edge retention are needed. A unique resin system helps minimize smearing and reduces heat build-up. The EX2 Deburring Wheel runs cool and resists loading due to its open-web construction. We did this to reduce the risk of part discoloration and warping, while extending the life of the wheel. The EX2 Deburring Wheel is available in fine and medium grade abrasives.Our Scotch-Brite™ EX2 Deburring Wheel is available with silicon carbide or aluminum oxide abrasive mineral. Silicon carbide is a synthetic mineral that is very sharp and commonly used for low-pressure applications such as paint prep and finishing. Aluminum oxide is a hard, blocky mineral that provides high cut-rate and long life. While silicon carbide breaks down faster than aluminum oxide, it produces a finer finish.Scotch-Brite™ industrial abrasives are unique surface conditioning products with abrasives incorporated into non-woven nylon or synthetic fibers. Combining abrasives with the fibers creates an abrasive system that delivers consistent results for the life of the product. We chose an open-web material that runs cool and is load resistant, which keeps the abrasive minerals cutting at high performance by limiting clogging of the fibers.

FREIGHT FREE on purchases with a subtotal of $4000.00 or more.

Our site states no returns allowed; however, if your order is defective or damaged, the order will be replaced with good product. In addition, we will attempt to return all your product (not only damaged product) if 3M grants the return based on various factors. Some items may be approved for return pending approval from 3M. Some but not all factors include if the item is a 3M stock item and elapsed time from receipt of product to issued return request. Note: 3M will not accept a return if the item is made to order or if the order is less than $600.00. Please double check accuracy of your orders prior to placing them. Details regarding if an item is stock or made to order can be found in the specifications tab of the item page. N = Made to order Item. S = Stock Item. We cannot guarantee any returns.

If you received a defective or damaged shipment, please email us at support@industrialgeneralstore.com explaining in detail the reason for requesting a replacement so we can contact 3M and initiate the return and new shipment.