3M™ Cold Shrink QS-III Splice Kit 5514A-350-AL, 350 kcmil, 1/case

The 3M™ Cold Shrink QS-III Shielded Cable Splices 5513A, 5514A, 5515A and 5516A Series are 15 kV class inline splices for joining tape shield, wire shield, UniShield® or longitudinally corrugated (LC) shielded power cables. It is a cold shrink design sized to fit Type MV-90 or Type MV-105 cables with copper, or aluminum conductor sizes ranging from 2 AWG-1000 kcmil (35-500 mm²).
Price: $627.92

(Case of 1 Kit)

Estimated Lead Time is 20 working days.
  • $627.92
  • Case of 1 - $627.92
Qty:  
  • Return Policy

    Our site states no returns allowed; however, in addition to a few exceptions, if your order is defective or damaged, the order will be replaced with good product. 

    • Weight
      10 lbs
    • SKU
      7100167490
    • UPC/ISBN
      00054007441069
  • Industry
    IB
  • Lead Time
    20
  • Manufacturer
    3M
  • SAP
    7100167490
  • 3M ID
    80611207558
  • UPC
    00054007441069
  • Product Formal Name
    3M™ Cold Shrink QS-III Splice Kit 5514A-350-AL, 350 kcmil, 1/case
  • Case Unit
    Case of 1
  • Unit of Measure
    Kit
  • Product ID
    5514A-350-AL
  • Estimated Lead Time
    20
  • Inventory Status Code
    N
  • Technical Information
    https://multimedia.3m.com/mws/media/144011J/3mtm-cold-shrink-qs-iii-inline-splice-kits-15-kv.jpg
  • Instructions/Manual
    https://multimedia.3m.com/mws/mediawebserver?mwsId=SSSSSuUn_zu8l00xM82Zm821Nv70k17zHvu9lxtD7SSSSSS--
  • Country of Origin
    USA
  • Return Policy
    No Return
  • Box Length (in)
    25.7
  • Box Width (in)
    7.7
  • Box Height (in)
    8.3
  • Bullets
    • Bullet 1
      - Inline splice for joining tape shield, wire shield, UniShield® or longitudinally corrugated shielded power cables
      - Special electrode design of the kit reduces the electrical stress at a critical cable/splice interface
      - Designed for feeder and distribution circuits, it transitions from shielded to neutral power cables and fits type MV-90 cables
      - Silicon rubber-splice body provides good high and low temperature performance, and the EPDM rubber jacket offers physical protection
      - Rated for 15 kV class cables
      - Factory-tested partial discharge and AC ensure reliability
  • Transportation
    • ECCN Number
      EAR99
    • Harmonized Tariff Schedule Number
      8546900000
    • UNSPSC Code
      26121600
    • United States Department Of Transportation Ground US DOT, 49 CFR
      NOT RESTRICTED, AS PER 49 CFR 171.4, MARINE POLLUTANT EXCEPTION
    • United States Department Of Transportation Vessel US DOT, 49 CFR
      NOT RESTRICTED, AS PER 49 CFR 171.4, MARINE POLLUTANT EXCEPTION
    • NMFC Item
      061205
    • NMFC Class
      110.0
    • NMFC Sub
      00
    • Transport Protective Service
      PROTECTIVE SERVICE NOT REQUIRED
    • International Air Transport Association
      NOT RESTRICTED, AS PER SPECIAL PROVISION A197, ENVIRONMENTALLY HAZARDOUS SUBSTANCE EXCEPTION
    • International Maritime Organization
      NOT RESTRICTED, AS PER IMDG CODE 2.10.2.7, MARINE POLLUTANT EXCEPTION
    • Flashpoint Transport
      No Flash Point
  • SKU
    7100167490
  • UPC/ISBN
    00054007441069

The cold shrink splice body is a one-piece molded design made of special formulated silicone rubbers, while the cold shrink jacketing is made of EPDM rubber for physical protection. Each splice manufactured is factory tested to provide reliability.The splices can be used with standard copper (Cu) or aluminum (Al/Cu) inline compression (crimp type) connectors, and can be used for size transitions within the listed kit size range. They are designed to exceed minimum industry test standards, and have a BIL rating of 150 kV (equal to a 25 kV voltage class). The 5513A, 5514A, 5515A and 5516A QS-III splices meet or exceed the 15 kV Voltage Class rating requirements of IEEE 404. Each kit makes one splice.Note: Cable sizes shown below are for standard insulation thickness. Final determining factor is cable insulation O.D.

FREIGHT FREE on purchases with a subtotal of $4000.00 or more.

Our site states no returns allowed; however, if your order is defective or damaged, the order will be replaced with good product. In addition, we will attempt to return all your product (not only damaged product) if 3M grants the return based on various factors. Some items may be approved for return pending approval from 3M. Some but not all factors include if the item is a 3M stock item and elapsed time from receipt of product to issued return request. Note: 3M will not accept a return if the item is made to order or if the order is less than $600.00. Please double check accuracy of your orders prior to placing them. Details regarding if an item is stock or made to order can be found in the specifications tab of the item page. N = Made to order Item. S = Stock Item. We cannot guarantee any returns.

If you received a defective or damaged shipment, please email us at support@industrialgeneralstore.com explaining in detail the reason for requesting a replacement so we can contact 3M and initiate the return and new shipment.