Standard Abrasives™ Buff and Blend Flap Brush 875015, 12 in x 2 in x 5 in FB120 20-71 A MED Hard Density, 2 per case

The conformability and consistent performance of our Standard Abrasives™ Buff and Blend Flap Brush makes it ideal for blending, cleaning, deburring and finishing on stainless steel, brass and aluminum, especially where a uniform and long line brushed finish is desired.
Price: $339.40

(Case of 2 Each)

  • $339.40
  • Case of 2 - $339.40
Qty:  
  • Return Policy

    Our site states no returns allowed; however, in addition to a few exceptions, if your order is defective or damaged, the order will be replaced with good product. 

    • Weight
      6.2 lbs
    • SKU
      7000121907
    • UPC/ISBN
      00051115332586
  • Industry
    IB
  • Lead Time
    2
  • Manufacturer
    3M
  • SAP
    7000121907
  • 3M ID
    66000008590
  • UPC
    00-51115-33258-6
  • Product Formal Name
    Standard Abrasives™ Buff and Blend Flap Brush 875015, 12 in x 2 in x 5 in FB120 20-71 A MED Hard Density, 2 per case
  • Brand-old
    Standard Abrasives
  • Brand
    Standard Abrasives
  • Case Unit
    Case of 2
  • Unit of Measure
    Each
  • Estimated Lead Time
    2
  • Grade
    MED
  • Grit/Micron
    Medium
  • Size
    12 in x 2 in x 5 in
  • Diameter
    12 Inch
  • Diameter (Metric)
    304.8 mm
  • Color-old
    Maroon
  • Inventory Status Code
    S
  • Data Sheet
    https://multimedia.3m.com/mws/media/563940O/standard-abrasives-quick-change-discs-for-disc-sanders.pdf&fn=61-5002-8236-5_2014_R1.pdf
  • Instructions/Manual
    https://multimedia.3m.com/mws/mediawebserver?mwsId=SSSSSuUn_zu8l00xMYtvPYt94v70k17zHvu9lxtD7SSSSSS--
  • Country of Origin
    USA
  • Product Form
    Brush
  • Attachment Type
    Center Hole
  • Mineral Type
    Aluminum Oxide
  • Form Type
    Flap
  • Max RPM
    2500 none
  • Return Policy
    No Return
  • Width
    12 in
  • Length
    2 in
  • Box Length (in)
    15.5
  • Box Width (in)
    15.5
  • Box Height (in)
    5.7
  • Bullets
    • Bullet 1
      Well-suited for finishing, cleaning, and blending applications on aluminum, brass and stainless steel
  • Transportation
    • ECCN Number
      EAR99
    • Harmonized Tariff Schedule Number
      6805301000
    • United States Department Of Transportation Ground US DOT, 49 CFR
      NOT REGULATED
    • United States Department Of Transportation Vessel US DOT, 49 CFR
      NOT REGULATED
    • NMFC Item
      033100
    • NMFC Class
      200.0
    • NMFC Sub
      01
    • Transport Protective Service
      PROTECTIVE SERVICE NOT REQUIRED
    • International Air Transport Association
      NOT REGULATED
    • International Maritime Organization
      NOT REGULATED
    • Flashpoint Transport
      No Flash Point
  • SKU
    7000121907
  • UPC/ISBN
    00051115332586

Quality Materials and Construction for Demanding Finishing Applications Standard Abrasives™ Buff and Blend products are made from tough, resin-reinforced nylon fiber with aluminum oxide abrasive grain. The durable high strength construction of our Standard Abrasives™ Buff and Blend Flap Brush provides aggressive, controlled action and a consistent, uniform finish without leaving behind parting lines. Non-woven construction conforms to workpiece contours, curves, and ridges and allows removing surface contaminants without eliminating critical detail or gouging the workpiece. Choose from a broad offering of sizes, densities and grades to suit many different finishing operations. A Buff and Blend Flap Brush is an ideal choice for: A grain finish on brass strike plates for door hardware A satin finish on builders’ hardware (cabinet handles, door knobs, and more) Satin finishes on soft metals Inline brushed finishes on aluminum and stainless cookware (pots and pans) Producing fine scratch patterns on utensils and cutlery prior to cotton buff and compound polishing Removing oxide from precious metals Blending flash and parting lines on aluminum die cast Featuring Consistent Finishes and Operator Comfort Flap brushes produce a consistent finish which does not reflect lines commonly attributed with ganged arbor hole discs. Density, pressure and angle determine the ability of the flap brush to remove burrs, oxidation and handling marks. The abrasive material provides ventilation which helps dissipate heat and, therefore, runs cooler. This provides consistent finishes without smearing or otherwise discoloring the work piece. Minimal vibration can reduce chattermarks on the workpiece and can lead to less operator and machine fatigue. Load-Resistant Construction Boosts Life and Performance Standard Abrasives™ Buff and Blend products are load-resistant to keep you cutting with fresh mineral. The gaps in the open web allow unwanted swarf to escape. Consequently, less debris clogs the abrasive, so the mineral can stay fresh, keep cutting sharp and deliver a consistent cut over the life of the product. As the fibers break down and fresh mineral is exposed, it reduces the likelihood of dull or blunt mineral smearing the surface, contributing to cleaner surfaces and less re-work. Furthermore, manual fatigue that may result from applying heavy pressure to a dull abrasive is reduced. The Many Benefits of Standard Abrasives™ Buff and Blend Products Standard Abrasives™ Buff and Blend products invigorate deburring, cleaning, blending and finishing applications by helping operators reduce finishing steps, minimize costs and achieve greater throughput. Each Buff and Blend product and grade offers unique benefits, so operators can choose from a versatile range of options to ensure superior performance on specific applications.

FREIGHT FREE on purchases with a subtotal of $4000.00 or more.

Our site states no returns allowed; however, if your order is defective or damaged, the order will be replaced with good product. In addition, we will attempt to return all your product (not only damaged product) if 3M grants the return based on various factors. Some items may be approved for return pending approval from 3M. Some but not all factors include if the item is a 3M stock item and elapsed time from receipt of product to issued return request. Note: 3M will not accept a return if the item is made to order or if the order is less than $600.00. Please double check accuracy of your orders prior to placing them. Details regarding if an item is stock or made to order can be found in the specifications tab of the item page. N = Made to order Item. S = Stock Item. We cannot guarantee any returns.

If you received a defective or damaged shipment, please email us at support@industrialgeneralstore.com explaining in detail the reason for requesting a replacement so we can contact 3M and initiate the return and new shipment.

Customers who viewed this product bought