3M™ Polyimide Hybrid Bond Diamond Wheels and Tools, 1V1, 5X3/8X2, X=3/8, V=45 D320 675PM - MMMPBDW41350-1

Our 3M™ Diamond Wheel 675PM are used in the production and sharpening of carbide cutting tools. This general purpose wheel is designed to give you the best form retention and a long wheel life at lower cut rates. It can be used with either oil or water based lubricants.
Price: $539.47

(Case of 1 Each)

  • $539.47
  • Case of 1 - $539.47
  • Return Policy

    Our site states no returns allowed; however, in addition to a few exceptions, if your order is defective or damaged, the order will be replaced with good product. 

    • Weight
      3 lbs
    • SKU
    • UPC/ISBN
  • Industry
  • Lead Time
  • Manufacturer
  • SAP
  • 3M ID
  • UPC
  • Product Formal Name
    3M™ Polyimide Hybrid Bond Diamond Wheels and Tools, 1V1, 5X3/8X2, X=3/8, V
  • Case Unit
    Case of 1
  • Unit of Measure
  • Product ID
  • Estimated Lead Time
  • Grit/Micron
  • Size
    5 x 3/8 x 2
  • Inventory Status Code
  • Country of Origin
  • Return Policy
    No Return
  • Width
  • Length
  • Bullets
    • Bullet 1
      - diamond Abrasive capable of cutting or shaping cemented carbide, ferrites and ceramics
      - polyimide bonding resists thermal and chemical deterioration
      - Designed to provide the BEST form retention and Longest wheel life
      - various wheel designs are Available for gashing, primary and Secondary relief and end Work
      - Arbor holes are Made to Customer specifications
  • Transportation
    • UNSPSC Code
    • United States Department Of Transportation Ground US DOT, 49 CFR
    • United States Department Of Transportation Vessel US DOT, 49 CFR
    • NMFC Item
    • NMFC Class
    • NMFC Sub
    • Transport Protective Service
    • International Air Transport Association
    • International Maritime Organization
    • Flashpoint Transport
      No Flash Point
  • SKU

High Performance GrindingOur polyimide diamond wheels are designed for high performance grinding on carbide. The 3M™ Diamond Wheel 675PM line is specifically designed for the production and sharpening of cutting tools, including end work, gashing and cutting primary and secondary relief edges. Primary relief involves removing material directly behind the cutting edge to enhance chip clearance. For secondary relief, a slight bevel is ground next to the primary relief. End work grinds a small relief angle on the tip of the tool, while gashing adds a slot along the cutting face to allow for chip flow. Each of these processes require the highest level of quality that our 3M™ Diamond Wheel 675PM provides.Heat Resistant BondingThese superabrasive wheels also use a polyimide resin bonding and are specially designed to resist thermal and chemical deterioration, which can occur during high speed grinding. This S rated bond is very hard and excellent for precision work on softer tool metals like carbide. This also allows for longer run times and longer over-all wheel life. Used in wet grinding applications with high volume flood coolant systems, this bonding material can be used with wither water or oil based lubricants for greater flexibility.3M provides a broad portfolio of superabrasive wheels used for your round tool relief and clearance angle applications. The 3M™ Diamond Wheel 675PM line features a variety of metal cores, including aluminum, steel, composite and copper, and can be cut with custom arbor holes to fit customer specifications. From short runs and re-sharpening to “lights-out” and long production runs, 3M has the wheel design to meet your needs.

FREIGHT FREE on purchases with a subtotal of $4000.00 or more.

Our site states no returns allowed; however, if your order is defective or damaged, the order will be replaced with good product. In addition, we will attempt to return all your product (not only damaged product) if 3M grants the return based on various factors. Some items may be approved for return pending approval from 3M. Some but not all factors include if the item is a 3M stock item and elapsed time from receipt of product to issued return request. Note: 3M will not accept a return if the item is made to order or if the order is less than $600.00. Please double check accuracy of your orders prior to placing them. Details regarding if an item is stock or made to order can be found in the specifications tab of the item page. N = Made to order Item. S = Stock Item. We cannot guarantee any returns.

If you received a defective or damaged shipment, please email us at support@industrialgeneralstore.com explaining in detail the reason for requesting a replacement so we can contact 3M and initiate the return and new shipment.