3M™ Marine High Strength Repair Filler, 46014, 1 gal, 4 per case
3M™ Marine High Strength Repair Filler restores damaged areas of fiberglass hulls, decks and other areas on boats. Our filler is a high performance product that is reinforced with short strands of fiberglass for added strength. Boat restoration professionals commonly use this product.
-
Return Policy
Our site states no returns allowed; however, in addition to a few exceptions, if your order is defective or damaged, the order will be replaced with good product.
-
IndustryIB
-
Lead Time2
-
Manufacturer3M
-
SAP7000000605
-
3M ID60980027225
-
UPC00-51131-46014-0
-
Product Formal Name3M™ Marine High Strength Repair Filler, 46014, 1 gal, 4 per case
-
Brand-old3M
-
Case UnitCase of 4
-
Unit of MeasureBottle
-
Product ID46014
-
Estimated Lead Time2
-
Inventory Status CodeS
-
Instructions/Manualhttps://multimedia.3m.com/mws/mediawebserver?mwsId=SSSSSuUn_zu8l00xl8mZ48t9Nv70k17zHvu9lxtD7SSSSSS--
-
Country of OriginUSA
-
ConsistencyPaste
-
Return PolicyNo Return
-
Box Length (in)13.6
-
Box Width (in)13.6
-
Box Height (in)9.7
- Bullets
-
Bullet 1- Filler restores damaged fiberglass hulls and decks on boats
- Short strands of fiberglass reinforce strength of filler
- Paste consistency allows application of vertical surfaces
- Non-staining and non-shrinking formula
- 3M™ Cream Hardener included
-
- Transportation
-
ECCN NumberEAR99
-
Harmonized Tariff Schedule Number3214100090
-
UNSPSC Code12350000
-
United States Department Of Transportation Ground US DOT, 49 CFRLIMITED QUANTITY
-
United States Department Of Transportation Vessel US DOT, 49 CFRUN3527, POLYESTER RESIN KIT, 4.1, III, LIMITED QUANTITY
-
NMFC Item050075
-
NMFC Class055.0
-
NMFC Sub00
-
Transport Protective ServicePROTECTIVE SERVICE NOT REQUIRED
-
International Air Transport AssociationFORBIDDEN PACKAGE SIZE EXCEEDS IATA QUANTITY LIMITATIONS
-
International Maritime OrganizationUN3527, POLYESTER RESIN KIT, 4.1, III, LIMITED QUANTITY
-
Flashpoint TransportNo Flash Point
-
-
SKU7000000605
-
UPC/ISBN00051131460140
3M™ Marine High Strength Repair Filler is a uniquely modified vinyl ester structural filler formulated with short strand fiberglass for non fairing applications. The fiberglass fibers interlock to give our filler additional strength compared to regular fillers. Filler is non staining, non shrinking and it comes with 3M™ Marine Creme Hardener.We recommend this product for filling and covering scratches, dings, rust outs, blemishes, pinholes and other simple surface defects that otherwise exhibit a true or fair line. Use this filler to level or even out depressions and low spots. 3M™ Marine High Strength Repair Filler comes in a paste consistency that can be applied on vertical surfaces. It offers a working time of 10 to 15 minutes and may be sanded in 30 minutes.Directions for use - Before using this product, please reference Product Label and/or Safety Data Sheet for Health and Safety Information:Must be used when surface, product and shop temperature are above 60 degrees Fahrenheit.Clean surface free of dust, grease, wax, oil and moisture. Laminate must be dry.Grind damaged fiberglass using a coarse grade (40 grit) 3M abrasive, and wipe clean with a tack cloth. Mix 3M™ Marine High Strength Repair Filler thoroughly. Next, apply desired amount of filler on a clean non porous mixing surface. Do not use cardboard.Add 2 percent 3M™ Marine Creme Hardener (1 1/2 inch strip to a golf ball sized amount of filler). Mix filler and hardener to a uniform color, making sure to break any air bubble that may have been introduced. Mix only what you will use in 15 minutes. Apply 3M™ Marine High Strength Repair Filler to a clean surface to be repaired. Apply additional filler no thicker than 3/8 inch per layer, building slightly lower
Our site states no returns allowed; however, if your order is defective or damaged, the order will be replaced with good product. In addition, we will attempt to return all your product (not only damaged product) if 3M grants the return based on various factors. Some items may be approved for return pending approval from 3M. Some but not all factors include if the item is a 3M stock item and elapsed time from receipt of product to issued return request. Note: 3M will not accept a return if the item is made to order or if the order is less than $600.00. Please double check accuracy of your orders prior to placing them. Details regarding if an item is stock or made to order can be found in the specifications tab of the item page. N = Made to order Item. S = Stock Item. We cannot guarantee any returns.
If you received a defective or damaged shipment, please email us at support@industrialgeneralstore.com explaining in detail the reason for requesting a replacement so we can contact 3M and initiate the return and new shipment.